CONVERTIDOR CUK PDF

Convertidor Cúk. L1 L2 C1. V1 uH 10u mH C2 R1 u. V3 D1 MUR TD = 0. V2 = PW = 45u. PER = 50u. V1 = 0. 0. Voltaje Inductor. A partir del modelo de tiempo continuo del convertidor, se obtiene el modelo . of a bidirectional coupled –inductor Cuk converter operating in sliding-mode. Cuk Converter. 0. Favorite. 4. Copy. Views. Open Circuit. Cuk Converter. Social Share. Circuit Description. Graph image for Cuk Converter. Circuit Graph.

Author: Ner Tojanris
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Software
Published (Last): 3 November 2017
Pages: 173
PDF File Size: 9.60 Mb
ePub File Size: 11.40 Mb
ISBN: 649-8-75180-215-6
Downloads: 35795
Price: Free* [*Free Regsitration Required]
Uploader: Kalkis

The reasons vary, with some being more obvious than others. In steady state, the energy stored in the inductors has to remain the same at the beginning and at the end of a commutation cycle. It requires two inductors these can be coupled or uncoupled and are typically matched in value and a coupling capacitor C5 between the input and output. The energy in an inductor is given by:.

Because the power transfer flows continuously via the capacitor, this type of switcher has minimized EMI radiation.

This state of operation is usually not studied in much depth as it is generally not used beyond a demonstrating of why the minimum inductance is crucial, although it may occur when maintaining a standby voltage at a much lower current than the converter was designed for.

It is essentially a boost converter followed by a buck converter with a capacitor to couple the energy. In other projects Wikimedia Commons. He received an associate degree in electronics from Bay Valley Technical Institute in Please Select a Region. In his rarely available brief moments of spare time, he writes bios and ponders what he would do if he had more spare time. This configuration often provides the best combination of size, efficiency and output ripple for a given output current. By using this site, you agree to the Terms of Use and Privacy Policy.

Please Select a Language. Its schematic can be seen in figure 1. Figure 7 below shows the LTused as an inverting charge pump upper circuit and a boost converter. However, engineers often unknowingly refer to these topologies by the wrong name, adding confusion to an area that already is a bit confusing. The LTC has a 3. Wikimedia Commons has media related to Cuk converters. However, unlike these converters, it can cpnvertidor operate in discontinuous voltage mode the voltage across the capacitor drops to zero during the commutation cycle.

  ALAMBRADO DE BONSAI PDF

Convertidor Cuk

It can be seen that this relation is the same as that obtained for the buck—boost converter. It is an inverting converter, so the output voltage is negative with respect to the input voltage. Therefore the topologies are not readily convertible from one to the other. With steady-state conditions i. From Wikipedia, the free encyclopedia. Unfortunately, many data sheets and online search parametric tables do not distinguish between the unique topologies, but rather lump them together as “inverting converters.

The current flowing from the input power source is cik in other words, current flows from the input when the power switch is closed or open. This page was last cyk on 10 Novemberat Charging a capacitor with a current source convetridor inductor prevents resistive current limiting and its associated energy loss.

It uses a capacitor as its main energy-storage component, unlike most other types of converters which use an inductor. This implies that the current through the inductors has to be the same at the beginning and the end of the commutation cycle.

Another difference between the topologies is the voltage at the switch node. Commons category link is on Wikidata. What does each topology do? The average values of V L1 and V L2 are therefore:. Why choose one topology over the other? DC-to-DC converters Cnvertidor regulation.

When the switch is closed, both inductors have an increasing current flow the current is ramping up, but since the current in L2 is negative the two currents ramps move in opposite directions.

Since we are dealing with power transfer, as the output voltage becomes more negative or the input voltage decreases, the peak inductor current increases, increasing output ripple noise; similarly, as the input voltage increases or the output voltage approaches 0V, the peak inductor current decreases.

  KALNIRNAY 2009 PDF

Output disconnect is inherently built into this single inductor topology. In addition to these circuits, the buck converter with the output referenced to ground, and the flyback converter are also capable of providing a negative output voltage.

Let’s look at the current flow during switching cycles for each topology. It also has higher peak current and output ripple than a Cuk converter with a similar output current.

Differences Between the Ćuk Converter and the Inverting Charge Pump Converter

The inverting charge pump is closely related clnvertidor a step-up converter because it combines an inductor-based step-up regulator with an inverting charge pump. For the inverting converter, this voltage is negative during the 2nd phase of the switch cycle. As both average voltage have to be zero to satisfy the steady-state conditions, using the last equation we can write:.

The objective is to show the advantages and trade-offs for the Cuk and inverting charge pump, followed by a brief discussion of the inverting topology, so you can make a more informed choice when selecting a negative output circuit topology that best suits your application.

For the Cuk, the simplified duty cycle assuming lossless diodes and switches is given by:. Since the power switch must see a negative voltage, the inverting topology is less versatile in that it can only be used for negative voltages. In both cases, the inductor current can be continuous and the input current can approach being continuous, convertdior it never is continuous.