EN ISO 6507-1 PDF

hardness test —. Part 1: Test method. Matériaux métalliques — Essai de dureté Vickers —. Partie 1: Méthode d’essai. STANDARD. ISO. Fourth edition. Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. I.S. EN ISO is the adopted Irish version of the European . The text of ISO has been approved by CEN as EN ISO.

Author: Voodoomuro Moshura
Country: Estonia
Language: English (Spanish)
Genre: Education
Published (Last): 28 August 2004
Pages: 420
PDF File Size: 19.97 Mb
ePub File Size: 1.32 Mb
ISBN: 509-3-92789-689-8
Downloads: 97582
Price: Free* [*Free Regsitration Required]
Uploader: Tushura

HV 2,5 24,52 N may be used. Independent of the type of sources, for hardness there are two possibilities for the determination of the uncertainty.

BS EN ISO 6507-1:2018

The check involves at least one indentation being made on a hardness reference block, calibrated in accordance with ISO VDI-Berichte 11pp. Setting up reading intentions help you organise your course reading. Because of this approach, it is important that the individual machine components are operating within the tolerances.

Type Document Web address https: If not, an indirect verification should be performed. The error b step 10 can be expected to be a systematic effect. In GUM, it is recommended to use a correction to compensate for such systematic effects. Reference number ISO In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

The finish of the surface shall permit accurate determination of the diagonal length of the indentation.

If the measuring system fails this test, appropriate action should be taken. The time from the initial application of the force until the full test force is reached shall not be less than 2 s nor greater than 8 s. If two adjacent indentations differ in size, the spacing shall be based on the mean diagonal length of the larger indentation.

NOTE There isk evidence that some materials may be sensitive to the rate of straining which causes small changes in the value of the yield strength. Introduction to Materials and Materials Forming Next: If the difference is greater, this shall be stated in the test report.

  DISKS F210 NETAPP PDF

NBN EN ISO 6507-1

M2 may lead to smaller values of ios. How do I set a reading intention To set a reading intention, click through to any list item, and look for the panel on the left hand side: The Red document status indicator indicates that the document is an old version The document sn likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS.

For these tests, a longer duration is permitted and this duration shall be specified as part of ido hardness designation see EXAMPLE in 4. Figure 1 — Principle of the test The Vickers hardness is proportional to the quotient obtained by dividing the test force by the sloping area of the indentation, which is assumed to be a right pyramid with a square base, and having at the vertex the same angle as the indenter. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

Have you read this? There is no general process of uso converting Vickers hardness into other scales of hardness or into tensile strength. Izo is a trademark of Adobe Systems Incorporated. Again there may be more recent versions of the document.

NBN EN ISO | NBN

This is particularly true for low-force Vickers hardness tests and Vickers microhardness tests, where the principal limitation will arise in the measurement of the diagonals of the indentation. The procedure for the determination of U is explained in Table D. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

For low-force hardness and microhardness tests, the maximum time shall not exceed 10 s.

  GEORGE FACER A2 CHEMISTRY PDF

ISO – Metallic materials — Vickers hardness test — Part 1: Test method

Every care has been taken to ensure that the file is suitable for use by ISO member bodies. Care should be taken, if standard uncertainties of type A and B are summarised, that the contributions are not counted twice see Clause 4 of GUM: Test method 1 Scope This part of ISO specifies the Vickers hardness test method, for the three different ranges of test force for metallic materials see Table 1.

Document Status Indicators The Green document status indicator indicates that the document is: Want access to British Standards? Their committees work with the manufacturing and service industries, government, businesses and consumers to facilitate the production of British, European and International standards. It is important that the test piece lies firmly on the support so that displacement cannot occur during the test.

NOTE 1 For indentation diagonals less than 0, mm, the increase of een uncertainty has to be considered. Verlag Berliner Union Stuttgart,pp The chain starts at the international level using international definitions of the various hardness scales to carry out international intercomparisons.

Here’s an example of what they look like: International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. It is strongly recommended that this procedure be applied for a maximum of one year after the successful passing of a direct verification. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the sphere.

Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or 65077-1, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.