Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Faushakar Dosho
Country: Barbados
Language: English (Spanish)
Genre: Politics
Published (Last): 28 November 2009
Pages: 185
PDF File Size: 2.28 Mb
ePub File Size: 3.44 Mb
ISBN: 977-1-91408-337-5
Downloads: 16438
Price: Free* [*Free Regsitration Required]
Uploader: Kagis

For older Hasssleblad lenses only: If you are using two batteries and they go dead, you will have to charge them for 28 hours to fully charge them up.

The nylon stop is a little more complicated. Every few months, place one of the wires on one end of the battery, and the other wire on the other end of the battery.

Here’s the easiest way that I’ve found to keep your battery in top shape:. There is, however, something that you can do to lessen the chances of this happening to you The little flat head of the release lever number 26 in the diagram from the service manual, page 18 pokes out of the back of the body but the shutter doesn’t fire.

You should see a brief, large round flash of light through the lens. It will either be the release button itself which, perhaps contrary to what you would expect, is not an electrical switch, but a mechanical plunger thingy. Camera body ELD Disassembly Right and left hand wall Remove or cut the foam plastic pad to get access to the screws The complete mirror can now be separated from the remainder of the assembly.


Rotate the knurled knob about two turns, insuring that the paper leader is being taken up on the supply spool.

HASSELBLAD Camera Manuals

It is for this reason that I completely disassemble the shutter and check each blade during an overhaul.

With one battery you should get about 1, shots, and 2, shots with two batteries. This way, you won’t get caught with two dead batteries. Your name or email address: As you wind the body, the body gear winds this magazine gear, which, in turn, advances the film. Then charge the battery for 14 hours, and it will be fully charged.

Turn the transport key on the magazine counter-clockwise to set the film counter to number 1. The socket will probably only have one wire, so you’ll have to solder or tape another wire to it.

Hasselblad 555ELD Service Manual

The rubber disk was replaced by a metal disk with a small rubber “doughnut”. If you see part of the shutter blades instead of a round flash of light, there is a problem, and that lens should not be used. I made this video to illustrate what’s happening: I often keep the button in the wrong hole when I am using a wire release – is your release button in the right hole?

By absorbing the shock, the brake would prevent the upper flap from cracking at the axle. The big problems happen when something goes wrong with the camera and you don’t notice it, like sluggish diaphragm blades in your lens, or a broken shutter blade that’s hiding at the edge of the shutter.

When it gets low enough, here’s what happens: Switching from O to T opens the shutter and curtains and exposure is go on and on till you return the lever from T to O. Move the “L O T” lever to the “L” position and charge the battery for about an hour. This space is where the first tooth on the body gear goes into.


500 EL/M won’t fire with pressing of release button

Then, there are two smaller pieces that are riveted to one end of the blade; one on the top and one on the bottom. Hasselblad cameras and lenses are designed so they perform properly with little or no special precautionary measures. For convenience use the aux.

Page 41 Camera body ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues and secure with eight screws Connect the mirror hinge to the two pins “A”. I just acquired a ELX to use exclusively for studio portrait work. Now look at the rear plate on one of your magazines. Mmanual the ASA dial on the back of the shell, then lift one side of the film advance key.

Because a bent or warped dark slide can create problems for you. Press the release button, and hold it in. Set the shutter speed ring to one second, and set the f stop ring to the largest opening smallest number.

Camera body ELD Adjustment Check that the flat side of gear is parallel with the rear section. Not only is this a pain in the neck job to do, but it is also very expensive. Comments to this Manuals Your Name.

Have you ever looked into your lens and gasped with horror at the sight of a broken shutter blade? Not many technicians take the time to do this.